| Customization: | Available |
|---|---|
| After-sales Service: | Yes |
| Warranty: | 5 Years |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Geocell height | 50mm,80mm,100mm,150mm,200mm |
| Welding spacing | 300mm-1000mm |
| Expanding size | 4.5×5m2, 6.5×4.5m2, 13.2×4.5m2 |
Geocell is honeycomb shaped structures, in material of HDPE, welded by highfrequency ultrasonic. Being flexible, geocell can be folded in transit and outspreaded filling with sand, stone or concrete in roadbed construction.
| No Gravel Base Required! The Geocell does not require a gravel base. This is due to both the depth and amount of compaction which takes place within the confined cells. Simply lay an approved geotextile below the grid and fill. The result is a savings in both labor and material cost. |
|
| Which Depth Cell do I need? For load support, the 3" Geocell with a gravel infill is rated for approximately 8,000 pounds and is best suited for light passenger vehicles, golf carts, horse paddocks etc. The 4" is rated at 40,000 lbs and is best suited for most driveway and parking lot applications. The 6" at 60,000 lbs is designed for emergency access or areas where heavy vehicles will be driving over regularly. The 8" is suited for specialty applications where heavy machinery will frequent. |
|
| Fabric for Beneath the Geocell (Required) & Accessories It is required that a layer of geotextile fabric is placed below the Geocell to prevent the gravel from absorbing into the ground while providing adequate strength and drainage. Additionally, J-Hooks, and staples / heavy duty zip ties are recommended to attached multiple panels. |
Gravel FillAggregate surface (crushed rock) |
|
Grass FillPermeable paving (turf / vegetated) |
|
UNDER ASPHALT & CONCRETE
When used under a asphalt or concrete surface the Geocell can help to provide stability and reduce the amount of aggregate required for stabilization.
|
|
SLOPE & SWALE STABILIZATION
Geocell can be used to stabilize hillsides and swales in additional to providing load support. The permeable geocells allow for water to flow through the material and help to keep the infill material from eroding.
|
|
|
• Erosion Control • Load Support • Slope Protection • Channel Protection • Retaining Wall • Ground Stabilisation |
| Lianyi HDPE Geocell | |||||||
| Material Properties | |||||||
| Polymer Density (ASTM D 1505) | g/cm3 | 0.935-0.965 | |||||
| Environmental Stress Crack Resistance (ASTM D 1693) | hrs | 6000 | |||||
| Carbon Black Content (ASTM D 1603) | % | min. 1.5% | |||||
| Nominal Sheet Thickness before texturing (ASTM D 5199) | mm | min. 1.27-5%,+10% | |||||
| Nominal Sheet Thickness after texturing(ASTM D 5199) | mm | min. 1.52-5%,+10% | |||||
| Material | HDPE | ||||||
| Texture | HDPE strip consists of a multiple rhomboidal indentations, over the entire strip on both sides of the strip.The indentations have a surface density of 22 to 32 per cm2 | ||||||
| Perforations | HDPE strip is perforated with horizontal rows of maximum 10mm diameter holes. Cell perforations area is less than 12% of cell surface area. | ||||||
| Cell/ Section Properties | |||||||
| Property | Unit | DTGS5 | DTGS8 | DTGS10 | DTGS15 | DTGS20 | |
| Weld Spacing | mm | 300-400 | 330-1000 | 330-400 | 330-400 | 330-400 | |
| Cell Depth | mm | 50, 80, 100, 150, 200 | |||||
| Seam Properties | Cell Depth | ||||||
| mm | 50 | 80 | 100 | 150 | 200 | ||
){kind=link}